Torsional, Axial and Lateral Bottom Hole Assembly Vibrations

Torsional, axile and Lateral Bottom crush Assembly Vibrations tasteal investigation of torsional, axial and squinty bottom hole assembly thrills1. launchIntroductionThe oil and gas industry is one of the largest and the most globalized industry in the world. Petroleum products include plastics, fuels, ointments and m some(prenominal) a(prenominal) more. With developments in world population, consumption and demand of petroleum products adopt outgrowthd. Primarily petroleum products argon utilise as energy sources. With an cast up in demand, different, unconventional sources atomic number 18 being explored. Drilling in itself is a complex process ascribable to the unknown formations in the landed estate. A hole is bore in the earth with a bit, and tubulars ar attached to it to fork over axial force and rotation. The tubulars atomic number 18 hol secondary through which the boring fluid is circulated to extract the cut rock. Once the hole is cut, the bit and tubular s are interpreted out, and a large tubular is pushed grim the hole and cemented just about the annulus to s pilfer the hole from caving in. The process is the same as boring a water well but with greater depth, compacts, temperatures and complexities. Some of the oil and gas sources are too deep or too complex to be explored, but with advanced technological developing in drilling, extended reach, multi sidelong and horizontal wells, it is now possible to extract unconventional oil and gas.VibrationsWhen an entity oscillates around its equilibrium pane, the entity is said to be in chill. In most of the cases vibrations are undesirable, as they cause injure to the arrangement and dissipate energy. When force or energy is imparted to a system, vibrations occur. In absence of external ardor, the vibrations are called free vibrations. Systems in state of free vibrations oscillate with natural frequencies, which are dependent on the properties of system. With the battlefront of external excitation, vibrations experienced by the system are called forced vibrations. Vibrations become increasingly large and are most damaging when the excitation frequency is close to one of the natural frequencies. This phenomenon is called resonance. When thither is an energy waste product from the system in terms of heat, sound, friction or every other method, the resulting vibrations are called damped vibrations.The drillstring assembly is a very long, slender system prone to excessive vibration due to the various forces acting on it. Primary forces on the BHA are contortion due to rotation and bit rock interaction, axial forces due to gravity and lateral forces due to bending of the long yell and hitting the walls of the borehole.Types of Drillstring VibrationsDrillstring vibrations are categorized base on the forces acting on it, which are Torsional, axile and Lateral forces. These forces correspond to the three types of vibration 1) Torsional vibrations, 2) Axial vi brations and 3) Lateral vibrations.Torsional Vibrations Drillstring is rotated from the surface to provide torsion or shear force to cut the rock.3. Experimental SetupA science laboratory-scale drilling baby carriage was constructed for the purpose of competing in Drillbotics International Student Competition. OU Drillbotics team participated and win the competition in 2015. The bud lodge restrictions limited the quality and quantity of sensors mounted on the semitrailer. The rig was upgraded in 2016 with the additional budget. The following sections describe the rig readyup and sensors installed, dividing them ground on the systems (i) Rig Structure, (ii) Hoisting System, (iii) Rotary System, (iv) Circulation System, (v) Measurement, instrumentation and Control System and (vi) Drillstring Assembly.Rig StructureRig Structure consists of three major parts substructure, mast and locomotion block.Rig SubstructureIn-house built structures have been found to be signifi dirty dogt ly cheaper than ready do structures in the market. Moreover, the former provides tractableness in the selection of dimensions, load ratings and practice styles. This substructure was designed to pass through doors, so the rig could be use for future educational purposes. The rig substructure was constructed using 1 square-iron electron tube with boilers suit dimensions of 84 x 27 x 36. To allow rig mobility, five commercial grade genus Castor wheels were installed, each with load capacity of 1000 lbs. A 47 x 27 shelf made of thick iron tag end was added for installation of circulation system and galvanic box. This left the rig with a stead of 37 x 27 x 36 to accommodate the rock sample.3.1.2 MastA mast of pottytilever design was constructed out of Aluminium, as shown in Fig. 3.1. kind 3.1 Rig mast laid graduate on the substructure superlativeConstructing the mast with aluminium reduced the weight by 2.5 times to that made by steel. A 10-inch-wide C-Channel was avowed by two 90 angle ramparts. The base was attached to the table with hinges for reclining and easy transport of the rig.3.1.3 travelling lay offThe travelling block slides on a p advertise of cable systemar guide rails attached to the mast. analog roller bearings or pillow blocks attached to the hind end of the travelling block provide near insipid motion. Two horizontal plates were bolted on the vertical plate. The upper plate acted as a mount for the AC push and lower plate supported the swivel. A torque sensor was dictated in among motor shaft and swivel. The total weight of the travelling block was measured to be 77.72 lbs. type 3.2 Travelling Block Assembly3.2 Hoisting SystemHoisting system components include a double acting air cylinder, pneumatic lines, a couple of pneumatic convertors (Fig. A.1 and Fig. A.2) and a compressed air supply line. Regulated compressed air-line up to 130 psi was hooked up to the pneumatic convertors. Two pneumatic lines from the convertors of maximum capacity great hundred psi controlled the air flow and committed to the inlet ports of the dual acting piston. Dual acting air piston has a 1.125 inch bore and a 36-inch stroke length. The system has a capacity to go up a load of 119.28 lbs.3.3 Rotary SystemA top drive system was installed with a 1 HP motor and a maximum rpm of 1170 on the motor mount of the travelling block. The motor shaft is connected to the omega torque sensor via a spring coupling. The torque sensor has a rotating shaft to shaft configuration with an operational speed of cholecalciferol0 rpm. The torque sensor is connected to the swivel via other spring coupling. The swivel was designed and fabricated in-house with pressure rating of 300 psi and brass outmost body for corroding resistance. The chrome plated rod is wear-resistant to the abrasion of the seals. Swivel rod is attached to an adapter at the base of the bottom plate. A four bolt brim mounted ball bearing prevents any load from being transmitted to the rotary assembly.3.4 Circulation SystemIt is important to remove cuttings from the hole to drill advertise ahead. To accomplish this, water, oil and foam based drilling fluids were taken into con spotration. Water from the city line without any additives was chosen as drilling fluid after taking cost of a closed eyelet system for recirculation and cost of additives and base fluids into account. It was excessively assumed that the work of drilling fluid on drillstring vibrations was negligible.A roller pump with a pressure rating of 300 psi was installed to circulate the water down the drillstring assembly. A 1.5 HP 3-phase motor powers the pump. The Omega digital display flow meter, which was installed after the pump, abide reminder flowrate up to 15 GPM. Pressure observeing is done by a pressure transducer of rating 500 psi. Pressure fluctuation of up to 50 psi was ascertained due to intermittent flow supplied by the roller pump. A pressure dampener was buil t with spare couplings and installed upstream to the flow meter. This provided smooth and invariable flow. An analog pressure gauge was mounted atop the dampener to monitor fluctuation. Rubber hose with a pressure rating of 300 psi connects the flow meter with the swivel. Drilling fluid from the swivel accordingly flows into the drillstring and comes out of the bit nozzles and out of the hole through the annulus. As the drilling fluid is just water, it is passed down the sewer line on with the cuttings and not recirculated.3.5 Measurement, Instrumentation and Control SystemThe Measurement, Instrumentation and Control system is the most important system in the automated rig. The sensors are mounted on the rig at various places for different functions. They provide analog entropy to the entropy accomplishment module Omega DAQ-3001. An galvanising box is mounted at the bottom shelf for shielding the card and other signal conditioners from electrical interference. The data from t he DAQ module transfers into the desktop computer, which is installed on the rig structure for control of the automated rig and memory and display of data. Excel-based VBA class is used for the operation of the rig.3.5.1 Measurement SensorsFollowing are the sensors installed on the rig to monitor performance of the rig and drilling process.3.5.1.1 Displacement Laser SensorAn aluminum trip is attached to the top of the travelling block with a reflective tape stuck on it. A Banner laser sensor is mounted about 0.5 inches higher up the travelling block on the mast. It can measure maximum switch up to 3.93 inches with an accuracy in the midst of 0.019 inch to 0.039 inch.3.5.1.2 Lateral Vibration Laser SensorTo measure lateral vibrations of the drillstring, an xyz laser sensor is used. It can measure distance from 1.57 inch to 6.29 inch with an accuracy of less than 20 micrometer. The sensor was earlier mounted on an aluminium plate attached to the travelling assembly. But the stri p was long and excessive vibrations due to bit rock interaction caused the strip to flap at naughty amplitude, providing inconclusive and erroneous data. at that placefrom the mounting structure was made of a square iron tubing to give a sturdier structure. The vibration amplitude was then reduced and could be observed only at excessive vibrations due to higher revolutions per minute and WOB.3.5.1.3 Optical rev SensorAn LED-based, reflective type opthalmic rev sensor, which can measure up to 15000 rpm, is mounted on the cage of swivel. Reflective tape is stuck on the spring coupling between the swivel and torque sensor. The sensor is mounted at an angle so that the reflective area increases for better measurement.3.5.1.4 tortuosity SensorIt is assumed that torque measured by the torque sensor is the torque due to bit-rock interaction. An Omega rotating shaft to shaft torque sensor has been mounted above the swivel with a torque rating of 64 inch-pounds.3.5.1.5 Axial Vibration SensorAn axial vibration senor is installed at the bottom plate of the travelling block adjacent to the flange mounted ball bearing. The VBT-1 vibration sensor has a micro-electro-mechanical system which sends a voltage proportional to the vibration velocity to the data acquisition module. It measures vibration velocity from 0-25 mm/sec.3.6 Drillstring AssemblyThe drillstring assembly comprises of 3 parts, Aluminum pipe, bit sub and bit.The pipe is made of Aluminum 6061 with an OD of 0.375 inch and a thickness of 0.035 inch. Both ends of the pipe have 3/8 NPT male compression fittings attached on it. It is connected on one end to 3/8 NPT female brass adapter which is connected to the swivel rod and other end is connected to 3/8 NPT female bitsub.The bit sub is made out of stainless steel for corrosion resistance. It has 3/8 female NPT threads on both ends. A roller sleeve with OD of 1.1 inch and ID of 0.9 inch is slide upon the bit sub to act as a stabilizer and provide smooth rotat ion. It has a counter bore to place constriction of various sizes to turn pressure drop down in the system.The bit is fabricated in house using stainless steel round bar and machined to replicate the baker huges bit provided for the competition. The cutters were bought from vendors and the OD of the cutters available was 0.5 inch. They are made out of carbide as argue to the diamond cutters provided and also wears down faster. The cutters are screwed on the cutter faces and are replaceable.4. MethodologyThis chapter describes the procedure of the experiments performed and the data cool. It also talks about some assumptions, sensor calibration and data analysis.4.1 Experimental ProcedureThe rig and all its components are powered on and the Excel program initiated. The program has a separate sheet which takes the variables of the experimental run as an input. The only variables changed for the set of experiments are RPM and WOB. Another variable, which is the height at which the string starts to rotate was also been varied but it did not have any effect on the data.A pilot hole of 1.25-inch diameter and 1-inch depth was drilled into the rock sample using a coring bit and hammer-chisel to insert a guide shoe in the hole. The 6-inch long guide shoe acted as a borehole wall and prevented bit walking. development a level indicator, the rock sample was adjusted to be horizontal.The drillstring was the attached to the swivel adapter and rig was then slid over the rock to align the drillstring and the guide shoe. Using the leveling screws the rig was jacked up to be horizontal.The inlet air pressure line and water line were opened up. Once all experimental variables were set, the program was initiated using the Start button. The first step of the program was to hoist the travelling block to the topmost position. At this point a safety bar used to keep the travelling block hoisted was taken away. The travelling block slowly get down down and at a time the bit wa s inside the guide shoe, top-drive motor and pump motor got activated and string started to rotate along with water pressurized inside the pipe. The bit gradually touched the rock and drilling process began.A endeavor run was carried out to check if the systems were working properly and data was being collected. A couple of millimeters were drilled during the trial run so that the hole got initiated.After a trial run, experimental runs were carried out. Each experiment was run for 6 min and stop using the Stop button in the program. The pump stopped pumping fluid and drillstring stopped rotation. Travelling block was gradually lifted up to the topmost position. After that impertinently experimental variables were set and the next run was carried out.Experiments were performed on 2 different rock samples. First set on a very effortful and compacted sandstone and the other on a very salving unconsolidated sandstone. UCS of the hard sandstone ranged from 6000 to 9500 psi while UCS for the piano sandstone ranged from 2000 to 5000 psi.4.2 data, Collection and AnalysisData was continuously collected by Omega data acquisition system module and stored in an excel sheet. The data of interest were WOB, RPM, tortuousness, Axial Vibrations, Lateral Vibrations and ROP. Different pieces were generated against variables of interest to observe dependency and behavior of the variable under investigation.4.2.1 WOB and RPM DataWOB is an independent variable with respect to our investigation. WOB was measured using a load cadre attached to the back travelling block connecting the piston. The calibration of WOB was carried out in the following procedure. The rig was slid on a weighing scale. A set number of determine were entered for voltage sent to the bottom pneumatic convertors. A unending voltage of 2 volts was sent to the top pneumatic convertor to provide a unvarying pressure of 20 psi resistance against erratic bouncing and to provide a unbroken friction betwe en piston and cylinder walls in either direction. Reading on the weighing scale was recoded as WOB. ab initio the WOB calibration was performed in a static condition. It was observed that WOB reading during the experiment was different than the expected values based on calibration. It was assumed that the change of conditions from static to dynamical was the cause of difference. Hence to simulate dynamic conditions while calibration, rig was constant quantityly hammered down with a mallet to cause the rig to vibrate and negate static friction. The stabilized reading on the scale was used for calibration. But hammering cool off did not replicate the vibrations happening during the drilling process and hence the WOB measurement by the load cell was different from expected based on the calibration. Hence average value of the WOB was calculated for complete experimental run and considered as the WOB which is being exerted on the rock for cutting process.The average WOB observed had a change of 19.9 % to -20.6 % from the expected input values. In actual drilling process, the WOB is never constant. As the drilling proceeds the WOB decreases and driller lowers the drill string to increase and maintain the set WOB. Hence a 20 % change from the set point is acceptable.RPM data was obtained from the optical RPM sensor which was calibrated using a handheld RPM sensor. At lower RPM the error was around 8 % and at higher RPM it lowered down to 0.5 %. So at lower levels the set point was reduced by 4 to repay for the error.4.2.2 Torque, Axial and Lateral Vibration DataA rotating shaft to shaft torque sensor was placed in between the motor and swivel with a spring coupling on each end. Torque was calibrated using a torque wrench. When run at idle conditions without any drilling action, torque reading obtained was assumed to be friction. That extra torque of 1.114 inch pounds was assumed to be a side force or the friction inside the swivel and other rotating parts such(p renominal) as the flange mounted ball bearing.A laser deracination senor was attached to the mast to incur the magnitude of lateral vibrations. It was aimed at the center of the drillstring such the pipe was always in range of the laser. The laser sensor was kept 4 inches away from the center of pipe. NPT connections are inherently non concentric and causes non-alignment of pipe. The pipe wobbled due to non-alignment and it oscillated far and near to the sensor. Hence there was a negative and a positive value for displacement. The most negative value of the displacement was used as a reference zero and complete data was shifted towards positive with -0.24165 inch as a reference zero. Greater the magnitude, pipe travelled farther away from the sensor indicating higher lateral vibrations.An axial vibration sensor was attached to the bottom plate of the travelling block. It had micro-electro-mechanical system inside to detect the vibration speed and send a proportional voltage signal for measurement. The sensor came calibrated from the maker and it had a direct vibration-velocity to voltage relationship provided by the manufacturer.4.2.3 ROP dataROP was directly calculated by the program by dividing the depth drilled by the time it took to drill and stored in the Excel sheet. As the delicate sandstone was difficult to drill the sensor could not measure any significant change in drilled depth along with the vibrations of the assembly and the error in measurement. Hence ROP data for Hard sandstone is not taken into consideration. Soft sandstone data was collected and analyzed for effect of vibrations and other parameters.4.3 Data AnalysisData was collected from the point where the bit touches the rock to the point when the program was stopped. All experiments were run for 6 minutes in which an average of 100 data points were collected in an excel sheet. An average of those data was calculated and stored. intermediate values of torque, axial vibrations and late ral vibrations were plotted against RPM and WOB separately. A turn of data was analyzed based on the plots. With increase of RPM, change of torque, axial and lateral vibration was observed. Same practice was carried out for WOB. The plots are shown in Appendix B.5. Results and DiscussionsTorsional VibrationsHard Sandstone Looking at the plots (Fig. 5.1), with an increase in RPM at constant WOB, torque gradually increases. At around 300 RPM, there is a sudden increase in some cases which then decreases. This behavior is unexpected and no conclusion has been found for the reason for the abnormality. It can be assumed that there would be some abnormally hard layer during drilling due to which such an increase is observed as no such trend was observed in the uniform soft sandstone. But familiar trend is a gradual increase in torque with an increase of RPM at constant WOB. No oscillation of torque was observed indicating absence of stick-slip.Figure 5.1 Torque vs. RPM plot at constant WOB for experiments on hard sandstoneAt constant RPM, with increase in WOB there is a gradual increase in torque (Fig. 5.2). No specific trend for RPM is observed as some of the low RPM cases also have higher torque than high RPM cases.Figure 5.2 Torque vs. WOB plot at constant RPM for experiments on hard sandstoneSoft sandstone observe the plot for soft sandstone (Fig. 5.3), a gradual increase in torque was observed with increase in ROM at constant WOB. No oscillation of torque was observed indicating absence of stick-slip.Figure 5.3 Torque vs. RPM plot at constant WOB for experiments on soft sandstoneThere is a clear and straightforward trend for increase in torque with increase in WOB at constant RPM (Fig. 5.4).Figure 5.4 Torque vs. WOB plot at constant RPM for experiments on soft sandstoneLateral VibrationsHard Sandstone game (Fig. 5.5) shows that there is a gradual increase of torque with increase in RPM at constant WOB.Figure 5.5 Lateral Vibrations vs. RPM plot at constant WOB for experiments on hard sandstoneNo general trend is observed for initial low WOB experiments (Fig. 5.6). With increase in WOB the lateral vibrations decreased in low RPM case and increase in high RPM cases.Figure 5.6 Lateral Vibrations vs. WOB plot at constant RPM for experiments on hard sandstoneSoft sandstone There is a general trend of increase of lateral vibrations with increase in RPM (Fig. 5.7) but it is not as significant as in hard sandstone.Figure 5.7 Lateral Vibrations vs. RPM plot at constant WOB for experiments on soft sandstoneThe data is too scattered to find a general trend for effect of WOB on lateral vibrations at constant RPM (Fig. 5.8). However, the trend at higher WOB shows a decrease in lateral vibrations. This can be attributed to the stiffening of the pipe due to higher axial load OR the pipe is hang and misaligned is making it bend more on the sensor side decreasing the deflection.Figure 5.8 Lateral Vibrations vs. WOB plot at constant RPM for experiment s on soft sandstoneAxial VibrationsHard Sandstone Axial vibrations follow a similar trend to torque (Fig. 5.9). With an increase in RPM, axial vibrations increased. Similar to the trend for torque, some cases have abnormally high vibration magnitude at 300 RPM which can be attributed to abnormally hard layer of formation.Figure 5.9 Axial Vibrations vs. RPM plot at constant WOB for experiments on hard sandstoneFollowing the general trend axial vibrations increased with an increase in WOB at constant RPM (Fig. 5.10).Figure 5.10 Axial Vibrations vs. WOB plot at constant RPM for experiments on hard sandstoneSoft sandstone With increase in RPM, axial vibrations increased (Fig. 5.11). However for soft sandstone the trend do not resemble the trend in torque. In fact, it resembles more to the trend in ROP (Fig. B.10). There is a sudden increase in axial vibrations at 700 rpm and then it decreases gradually.Figure 5.11 Axial Vibrations vs. RPM plot at constant WOB for experiments on soft san dstoneThe data is too scattered to find a general trend for relationship between WOB and axial vibrations (Fig. 5.12).Figure 5.12 Axial Vibrations vs. WOB plot at constant RPM for experiments on soft sandstone5.4 Effect on ROPHard Sandstone No significant data available for any analysis.Soft sandstone ROP increases with an increase in RPM at constant WOB (Fig. 5.13). It peaks at around 700 RPM and then it decreases.Figure 5.13 ROP vs. RPM plot at constant WOB for experiments on soft sandstoneAt higher RPM, higher WOB has an increased effect on ROP (Fig. 5.14). But no dependence of WOB can be seen at lower values of RPM.Figure 5.14 ROP vs. WOB plot at constant RPM for experiments on soft sandstone6. Conclusions and RecommendationsConclusionsAt constant WOB, with increase in RPM, increase in lateral vibrations in hard sandstone is higher than in soft sandstone which indicates that lateral vibrations also depend on type of formation.Axial vibrations are highly dependent on torque. No enumerate what RPM, WOB or the formation type is taken into account if there a change in torque, like change will be observed in axial vibrations.WOB has less effect on excitation of axial vibrations in soft rocks and more effect in hard rocks. Hence the setpoint WOB should be decreased for drilling into hard rocks.RPM of 700 is the highest RPM which can be used to obtain highest ROP without taking the increased vibrations into account. Increase of RPM further lowers the ROP which can be attributed to such increased vibrations and velocities that the bit does not get enough time to contact and drag the rock surface.6.2 Recommendations and Future WorkAlthough the design of the rig was optimized, there is always room for improvement. With an increase in budget and limited design constraints, the rig can be constructed better. Following are the recommendations for upgrading the rig.The software program used for the control algorithm can be upgraded to Labview or Dasylab which are more user friendly for programming the automation and control architechture.Using Labview or Dasy lab will allow to operate on a faster computer with a recent operating system which will help in faster data collection and storage.A vibrating element can be attached to the travelling block when WOB calibration is performed so that error due to change in friction values can be negated.The spring couplings attached to the torque can be upgraded with a higher torque rating to prevent failure at higher vibrations.A stable support structure for the torque sensor and laser deflection sensor can be provided.If the bit can be obtained or manufactured with diamond coated cutters, then a set of experiments can be designed where relationship could be examined between RPM, WOB and the depth of cut.Forward and backward whirl characterization experiments could be performed with improved sensors for detection of whirl rates.Hammering action can be included in the drilling action and its effect on ROP, lateral vibrations, torque and axial vibrations could be analyzed.ReferencesBraun, Simon G. Ewins, David J. Rao, Singiresu S.. (2002). Encyclopedia of Vibration, Volumes 1-